Anchor

3M

Comparison Chart

#111	43 mil stencil designed for hand-cutting. White liner. Use with filler #211.
#112	48 mil stencil designed for hand or machine cutting without reversing the liner. Red liner. Use with filler #211.
#116	33 mil, pin feed, high-tack computer stencil for use on raw wood surfaces and urethane foam board. Clear liner.. CAUTION: has a very aggressive adhesive - not recommended for use on some woods or on pre painted, pretreated or glass surfaces. No filler required.
#117	33 mil, pin feed, computer stencil. Medium-tack version of #116, designed for pretreated and pre painted surfaces and soft woods. Also used on stone, glass, tile and pretreated urethane foam board. Clear liner . Use with filler #211.
#120	33 mil , multipurpose, hand-cutting, medium-tack stencil designed for shape and depth carving in glass, pretreated, pre painted or soft woods. Dark blue liner. Can also be used on tile, pretreated urethane foam board and Plexiglas. No filler required.
#123 #123Y	48 mil stencil designed for machine cutting. Blue liner. Clear plastic sheet laminated serves to hold letters and designs in place (yellow plastic #123Y). Use with filler #223 or #333
#124 #124Y	48 mil stencil, slot punched, computer stencil same construction as #123. Blue liner. A sheet of clear 1-mil polyester film serves to hold letters and designs in place (yellow film #124Y). Holes are punched through liner and rubber. Use with filler #223.
#125	36 mil stencil, high-tack, hand-cutting , designed for sandblasting on raw wood and urethane foam board. Orange liner. No filler required. CAUTION: This has a very aggressive, adhesive not recommended for use on soft woods or on pre painted, pretreated or glass surfaces.
#128	18 mil hand cut stencil is designed primarily for light frosting and medium depth etching on glass. Can also be used on wood, tile, acrylic, and pretreated urethane foam board. Paper liner removes easily. Use with filler #211.
#129Y	45 mil stencil designed especially for dual pin feed roller computer cutters. Rubber is trimmed back from edges, so only the liner runs through the computer sprocket system. A sheet of yellow 1-mil mylar serves to hold letters and designs in place. Use with filler #223
#153	33 mil Designed for use on a friction-feed computer. Rubber is trimmed back from edges so wheels can clamp down on the 5-mil mylar liner. Use filler #211.
#154 #154Y	48 mil computer stencil with same construction as #123 stencil. Blue liner. A sheet of clear 1-mil mylar serves to hold letters and designs in place (yellow mylar #154Y). Holes are IBM configuration. Use with filler #223
#157	33 mil pin feed stencil. Same construction as #117 computer stencil except hole patterns for use on computerized cutters with a 1/2” on center sprocket system. Use with filler #211.
#158	46 mil computer stencil. Designed for use on plotters with sprockets 1/2” on center only IBM configuration. Use with filler #211.

Filler 211 - Produce superior results w/stencil styles
#111, #112, #117, #128, #157,#158
Filler 223 - For use w/stencil styles #123(Y), #124(Y),
#129Y, #154(Y)
Filler 333 - Use with all medium tack Anchor stencils.

#519Y	48 mil tan rubber designed for machine cutting. White film liner. Yellow inner liner supports center of letters, numbers, and designs. Use with filler #2. (Filler #3 for axed or frosted surfaces).
#519YS	48 mil tan rubber designed for computer cutting-slot punched for use on Gerber plotter. Yellow inner liner.
#519YT	48 mil tan rubber designed for computer cutting-tractor feed form. Yellow inner liner
#520	45 mil tan rubber designed for hand or machine cutting. Transparent film liner. Use with filler #2.
#520S	45 mil tan rubber designed for computer cutting -slot punched for use on Gerber plotter.
#520T	45 mil tan rubber designed for computer cutting -tractor feed form
#2 Filler - used w/ hand-cutting or machine cutting stencil on polished surfaces. #3 Filler - used w/ die-cutting stencil on axed or frosted surfaces.

This product is used in place of stencil filler. For cemetery lettering, bricks, frosted panels, and grassmarkers. After blasting, simply remove stencil. Transfer tape adheres to the stencil, so no clean up is needed. 2” x 60 yd.
superior results w/stencil styles. Cat. No. TAPEADTR